Illinois coverage · Written offers
DeKalb, IL Industrial Electrical Equipment Purchase and Removal
We are a direct buyer, not a broker. In DeKalb that distinction shows up on the dock: a broker's number is a guess that gets revised once their buyer sees the gear. Our offer is written against your nameplate photos and counts, itemized line by line, and it holds. We fund it ourselves and pay before the load moves.
Same-day written offer
Get a Written Offer
Send the asset list, or just describe what is in the room. We come back the same business day with a written, itemized offer.
Faster: call 954-740-1983
Email an asset list to electricalequipmentbuyers@gmail.com
Mon–Sat, 7am–7pm CT. We never resell your contact information.
- Location
- DeKalb, IL
- State
- Illinois
- Utilities
- ComEd, Ameren Illinois, City Wat
- Offer
- Same business day
- Payment
- Before load-out
- Phone
- 954-740-1983
This city
Buying electrical equipment in DeKalb
Coverage in DeKalb is run off our Illinois routing along I-55, I-57, I-80, I-88 and I-294. Coordination with ComEd, Ameren Illinois, City Water Light and Power on clearances, metering removal and final disconnect is part of the scope, not a change order. Chicago and its collar counties give us the widest range of equipment on this site, from century-old switchgear in loft conversions to switchboards pulled out of Loop high-rises still under warranty. The industrial ring through Joliet, Cicero and the Calumet side runs railcar, tank and metals operations with heavy motor loads. Downstate is a different business entirely: the agricultural processing plants at Decatur and Peoria, the Ameren Illinois distribution system and the refineries in the southwest corner. Bus duct and bus plug work shows up here more than anywhere, because so much Chicago-area industrial and institutional building was wired on busway and the plugs come out by the pallet during renovations.
The sequence on a DeKalb job is short. You send nameplate photos or a list. We come back the same business day with a written itemized offer and a proposed removal window. If you accept, we survey access — door widths, floor loading, dock height, whether the room is still energized — then mobilize, lock out, disconnect, unbolt, rig, load and sweep. Payment lands before the trailer leaves.
Equipment
What we buy in DeKalb
Fourteen categories. We buy every one of them at DeKalb sites.
Bus Plugs
Fusible switch and circuit-breaker plugs
30 A – 1,200 A fusible and breakerBus Duct & Busway
Feeder and plug-in, copper and aluminum
225 A – 5,000 A runsElectrical Switchgear
Low and medium voltage, indoor and outdoor
480 V – 38 kV, up to 5,000 AGenerators
Standby, prime and mobile sets
100 kW – 3 MW diesel and gasTransformers
Pad-mount, dry-type, substation, unit
75 kVA – 50 MVAPanelboards & Switchboards
Panelboards, switchboards, distribution
100 A – 4,000 AWire & Cable
Copper and aluminum, new and reclaimed
#12 AWG – 1,000 MCMCircuit Breakers
Molded case, insulated case, air, vacuum
15 A – 6,000 A framesMotor Control Centers
Low and medium voltage MCCs
MCC line-ups, buckets, VFD sectionsSubstations
Up to 138 kV primary
Complete unit and station substationsTransfer Switches
Automatic, manual, bypass-isolation
100 A – 4,000 A ATSCapacitors & Power Quality
Fixed and automatic capacitor banks
50 kVAR – 10 MVARComplete Plant Lots
One deal, one crew, one number
Whole-facility electrical scopeValuation
What drives the number
Transformer oil is the item sellers in DeKalb worry about most, and fairly so. We test it, drain it, manifest it through licensed handlers and hand you the documentation. PCB-suspect units are handled under their own waste profile. The cost of that handling is already inside the offer, so nothing surprises you after the fact.
| Input | Detail |
|---|---|
| Condition | Working, retired, water-damaged, or already dismantled |
| Support | Are breakers and parts still available for this line-up? |
| Copper | Windings, bus bar and cable weight |
| Access | Rigging path, crane need, dock reality at the DeKalb site |
| Freight | I-55, I-57, I-80, I-88 and I-294 |
Safety
Safety and documentation
Safety is scope, not a brochure page. Crews working in DeKalb operate to NFPA 70E for arc-flash boundaries and PPE, follow OSHA 1910.147 lockout and tagout with our own locks and written procedures, and hold a daily job safety analysis before the first bolt turns. We do not energize, test or operate your equipment — isolation is verified with your electrician before we touch anything.
Paper you receive
Certificate of insurance before we mobilize, a written itemized offer, a signed bill of sale, and load documentation for every trailer. If your compliance team needs something specific, ask before we schedule.
Nearby
Nearby cities and buyer desks
We cover the whole Illinois market, so if your equipment is not in DeKalb itself, one of these is probably closer:
Common questions
DeKalb questions
Do we have to disconnect the equipment before you arrive?
No. We handle removal. Your electrician or the utility performs the final isolation and we verify it; from there our crews lock out, cut and cap cable at the gland, unbolt the sections, skate them out and load them. If the DeKalb room is still partly live we phase the work.
How do you handle transformer oil in DeKalb?
Oil is tested, drained and manifested through licensed handlers, and you receive the documentation with your paperwork. PCB-suspect units go under a separate waste profile. Nothing is left on your pad in DeKalb and nothing gets dumped — the handling cost is already in the offer.
When do we get paid?
Before the equipment leaves your DeKalb dock. Wire, company check or cashier's check, whichever your accounting group prefers. On large phased projects we pay per load as it ships rather than holding everything until the end.
What if the equipment is old or has no test records?
We still quote it. Records raise the number — a NETA test report on a breaker or a transformer is the single document that most improves what we can pay — but their absence disqualifies nothing. We price DeKalb equipment on what our technicians and the replacement market say it is worth.
Are you insured to work inside our DeKalb facility?
Yes. We carry general liability, auto, workers' compensation and umbrella coverage, and we issue a certificate naming your entity as additional insured before crews mobilize to DeKalb. We also complete vendor onboarding, background checks and site-specific safety orientation on request.
Can you work nights, weekends or during a shutdown in DeKalb?
Regularly. Most electrical removals happen outside production hours because that is when circuits can be released. Night, weekend, holiday and turnaround windows in DeKalb are normal scheduling for us, not a premium service.
Electrical equipment in DeKalb?
Photos of the nameplates are enough to start. Written offer the same business day.